Introduction
A band pass filter is an electronic device or circuit that allows signals between two specific frequencies to pass. That is, allowing signals in a specific frequency band to pass while shielding other frequency bands. In other words, a bandpass filter attenuates frequency components in other ranges to an extremely low level, as opposed to the concept of a bandstop filter. For example, the RLC tank is an analog bandpass filter, it is a resistor  inductor  capacitor circuit (RLC circuit). These filtering circuit can also be made by connecting lowpass filters and highpass filters.
How to Design Band Pass Filter Circuit
Catalog
Ⅰ Band Pass Filter Circuit Characteristics
An ideal band pass filter should have a completely flat pass band, no amplification or attenuation. And all frequencies outside the pass band will be completely attenuated. In addition, the conversion outside the pass band is completed in an extremely small frequency range. But in fact, there is no ideal bandpass filter. Because the filter cannot completely attenuate all frequencies outside the desired frequency range, especially there is an attenuated but not isolated frequency range outside the desired pass band. This is usually called the filter rolloff phenomenon, and it is expressed in dB per decade of attenuation amplitude. Generally, the filter design should ensure that the rolloff range is as narrow as possible, so that the performance of the filter is closer to the design requirement. However, as the rolloff range gets smaller and smaller, the pass band becomes no longer flat and causes ripples.
The highpass filter has a low cutoff frequency, and the lowpass filter has a high cutoff frequency. When the high cutoff frequency is lower than the low cutoff frequency, combining the two circuits, and it is possible to design a band pass filter. The gain of the band pass filter is adjusted by the feedback resistor and the current limiting resistor.
Figure 1. Band Pass Filter Circuit Parts
A band pass filter with a high quality factor refers to a filter with a narrow pass band. In other words, a highQ factor means that fewer unwanted frequency signals will pass. A lowQ factor means that the pass band is very wide, to allow a wider range of frequencies to pass through.
Ⅱ Band Pass Filter Parameters
2.1 Center Frequency
It usually defined as the midpoint between the two 3dB points of a band pass filter (or a band stop filter), generally expressed by the arithmetic average of the two 3dB points. It is a frequency when the impedance of the entire circuit is a real number.
2.2 Cutoff Frequency
It refers to the frequency point on the right of the lowpass filter and the frequency point on the left of the high pass filter in the pass band. That is, the boundary frequency. It is usually defined as a standard by 1dB or 3dB relative loss point. The band pass filter has two cutoff frequencies, the low cutoff frequency fp1 and the high cutoff frequency fp2.
2.3 Bandwidth
The difference between two cutoff frequencies. The bandwidth is defined as B=fp2－fp1.
2.4 Quality Factor
The reciprocal of the damping coefficient is called the quality factor, which is an important indicator of the frequency selection characteristics of band pass and band stop filters. In short, it is the ratio of the center frequency to the bandwidth. What’s more, it can be used to describe the shape of the transfer function graph.
Ⅲ Types of Band Pass Filter
3.1 Active Band Pass Filter
Figure 2. Active Band Pass Filter Circuit
The active band pass filter is a cascade of highpass and lowpass filters and amplifier components. The circuit diagram of the active band pass filter consists of three parts. The first part is the highpass filter. Then, use the op amp for amplification. The last part of the circuit is the lowpass filter.
3.2 Passive Band Pass Filter
Figure 3. Passive Band Pass Filter Circuit
Passive band pass filters are a combination of passive highpass and lowpass filters. Passive filters use only passive components, such as resistors, capacitors, and inductors. Therefore, passive band pass filters are also used as passive components and do not use op amps for amplification.
Ⅳ Band Pass Filter Equation
4.1 Cutoff Frequency of Band Pass Filters
The characteristic of the band pass filter is that the output signal amplitude in the pass band is independent from the frequency. When f<fp1 or f>fp2, the output signals attenuate quickly. The amplitudefrequency characteristics are shown in the figure:
Figure 4. BPF Bandwidth
(The broken line is the ideal BPF frequency characteristic, and the solid line is the actual BPF frequency characteristic)
The resonance frequency is between fp1 and fp2, where the gain of the filter is the largest, and the bandwidth of the filter is the difference between fp2 and fp1.
It can be seen from the frequency characteristics of BPF that it can be composed of LPF and HPF in series, as long as the fpL of LPF (ie, fp2 of BPF) is greater than fpH of HPF (ie, fp1 of BPF).
4.2 General Form of Secondorder BPF Transfer Function
Frequency Characteristics
Where Aup is the passband magnification, center frequency , Q factor
Normalized frequency characteristics
Normalized amplitude  frequency characteristics
Figure 5. Amplitude  frequency Characteristics
Figure 6. Frequency Characteristics
It can be seen that the frequency characteristic of the band pass filter is completely determined by the center frequency ωo and the quality factor Q.
When f>fo, as the frequency f increases, the amplitude increases. According to the definition of cutoff frequency, the denominator of amplitudefrequency characteristic , that is (since f>fo, take a positive value)
1) Upper cutoff frequency
（take a positive value）
When f<fo, as the frequency f decreases, the output signal amplitude will decrease. According to the definition of cutoff frequency, the denominator of amplitudefrequency characteristic , that is (since f<fo, take a negative value)
2) Lower cutoff frequency
（take a negative), get the bandwidth
When the center frequency fo and bandwidth B (or Q) are known, the upper and lower cutoff frequencies fp1 and fp2 can be calculated. On the contrary, when the upper and lower cutoff frequencies fp1 and fp2 are known, the center frequency fo and bandwidth B (or Q) can be calculated.
(where ),
4.3 Secondorder Band Pass Filters
A simple secondorder band pass filter circuit is shown in the figure below, where R1 and C1 constitute a lowpass filter circuit, and C2 and R3 constitute a highpass filter circuit.
Figure 7. Secondorder Band Pass Filter Circuit
(1) Transfer Function
In order to reduce the amount of parameters matching, generally take C1=C2=C
Take , , that is
The transfer function can be obtained by using the node current method.
(2) Frequency Characteristics
where bandpass amplification (The negative sign means that the input and output are inverted. Because the filter circuit is an inverting filter.)
Center frequency (C1=C2=C), Q factor
When Aup, Q, and ωo are known, the resistance of each resistor is (R3 can be calculated with ωo/Q)
, (Aup<2Q^{2})
When the pass band amplification factor Aup is small, Q should not be too large (that is, the simple secondorder BPF has poor selectivity), otherwise R2 will become very small (R2 is generally greater than 1K), which will attenuate the input signal seriously. In order to make the system stable, Aup is generally between 1 and 10, and Q can be between 1 and 20.
(3) Design Steps
Example: It is known that Aup=5, center frequency fo=450Hz, bandwidth B=200Hz (). Try to calculate the parameters of the bandpass filter and verify.
First, according to the center frequency fo, check the parameter table and determine C1, C2, and operational amplifier parameters according to the nominal value.
fo=450Hz, take C1=C2=0.01uF(103 capacitor). Since the center frequency is not high, the requirement can be met by using LM358 operational amplifier.
Second, calculate the resistance of each resistor. Among them, the range of R1 and R3 should be between 10K ~510K, and R2 should be between 1K ~100K, otherwise the capacitor C needs to be reselected.
Substituting the relevant parameters into the above formula, the result is R1=15.9K, R2=15.5K, R3=159K.
Third, use simulation software to verify on the computer, and try to take the nominal value of each relevant resistance. The simulation schematic diagram and simulation results are shown in the figure below. The result values obtained from the AC small signal analysis and transmission characteristic analysis basically meet the requirements.
Figure 8. Filtering Circuit with LM358
Figure 9. Simulation Schematic Diagram
Figure 10. Voltage  Time Simulation (ui)
Figure 11. Voltage  Time Simulation (ui, uo)
The circuit requires a small number of components, and it can work with dual power supplies or with a single power supply (the noninverting termination is connected to a 1/2Vcc bias potential). In fact, it is widely used in single power supply systems. Because the quality factor Q cannot be too high. Almost all band pass filter circuits with a larger bandwidth B (with a smaller Q value) adopt this circuit form.
4.4 HighQ secondorder Band Pass Filters
The highQ secondorder band pass filter circuit is shown in the following figure. This circuit can work with dual power supplies or single power supplies, which is convenient to use in a single power supply system. Since the Q value can be made larger, it is particularly suitable as a band pass filter.
Figure 12. Bandpass Filter Circuit
(1) Transfer Function
In order to reduce the amount of parameters matching, generally take C1=C2=C
Where , , that is , , getting
The transfer function can be obtained by using the node current method.
(2) Frequency Characteristics
, where bandpass amplification
Center frequency , Q factor
In order to make the system stable, Aup and Q must be greater than 0, that is, 2R_{f}R_{4}R_{F}R_{3}>0, which must be guaranteed . Adjusting can control Aup and Q. is more closer to 2, the greater the Aup and Q values. Adjust the capacitor C to select the center frequency ωo. When the values of Aup, Q and ωo are known, and the ratio between and is determined, the resistance of each resistor is
, ,
(3) Design steps
Example: It is known that Aup=5, center frequency fo=1kHz, bandwidth B=50Hz (). Try to calculate the parameters of the bandpass filter and verify.
First, according to the center frequency fo, check the parameter table and determine C1, C2, and operational amplifier parameters according to the nominal value. (Aup: 1 ~10)
fo=1kHz, take C1=C2=0.01uF. Since the center frequency is not high, the requirement can be met by using LM358 operational amplifier.
Second, according to the value of Aup and Q, initially determine the value of and .
Since Aup and Q are large, is 1.8, is 0.5, and is 3.6.
Third, calculate the resistance of each resistor. The range of R1 and R3 should be between 10K and 510K, and R2 should be between 1K and 100K. Otherwise, the ratio of and needs to be reselected.
Substituting the relevant parameters into the above formula, the result is:
R1=229K, R3=63.7K, R2=4.18K, R4=127.4K: RF takes 36K, Rf takes 10K.
Fourth, use simulation software to verify on the computer, and try to take the nominal value of each relevant resistance. The simulation schematic diagram and simulation results are shown in the figure below. The result values obtained from the AC small signal analysis and transmission characteristic analysis basically meet the requirements.
Figure 13. HighQ BPF Circuit
Figure 14. Voltage  Frequency Simulation
Figure 15. Voltage  Time Simulation
4.5 Dualoperational Amplifier BPF (HighQ)
The BPF circuit with highQ value formed by dual operational amplifiers is shown in the figure. With fewer components, a very highQ value can be obtained when the pass band amplification factor Aup is fixed equal to 2, so it is also a commonly used BPF circuit.
Figure 16. Dualamp BPF
(1) Transfer function
According to the rule of futility, where
, , that is
, where
, so
(2) Frequency Characteristics
Compared with the standard form of the secondorder BPF transfer function, the following parameters can be obtained:
passband magnification , , center frequency
When R4=R5,R2=R3=R,C1=C2=C, Aup=2, , （）
It can be seen that when Aup=2 (that is, when R4=R5), the value of Q can be very large.
(3) Design steps
According to the center frequency fo, check the parameter table to determine C. When C is determined, the resistance R is calculated from the center frequency. Meanwhile, etermine R1 based on the Q value.
4.6 Secondorder Band Pass Filters (Voltagecontrolled Type)
The secondorder voltagecontrolled BPF is shown in the figure. Among them, R1 and C1 constitute a lowpass filter, R2 and C2 constitute a highpass filter. (The voltage positive feedback is introduced through the voltage R3 to form a voltagecontrolled bandpass filter.)
Figure 17. Secondorder Bandpass Filter (voltage controlled)
Rf/RF cannot be 3 to avoid selfexcitation.
(1) Transfer Function
Where ，that is , , so
The transfer function can be obtained by using the node current method.
In order to reduce the amount of parameters matching, generally take R1=R3=R,R2=2R,C1=C2=C
Where
In order to make the system stable, the coefficient of the first term in the denominator must be larger than 0, that is, 3−Auf>0, in other words, Auf<3.
(2) Amplitude  frequency Characteristics
where bandpass amplification , center frequency , Q factor
It can be seen that the closer Auf is to 3, the larger the Q value. The narrower the pass band B, and the better the selectivity.
(3) Design Steps
According to the center frequency, look up the table and initially determine C1=C2=C
calculate resistance , that is ,
Calculate bandwidth based on upper and lower cutoff frequencies , Calculate the quality factor
Calculate by Q and determine the resistances Rf and RF.
As a special case, the center frequency fo=1KHz is known, so C1=C2=C=0.01uF
，R2=2R=31.8K
, getting Auf=2.95, that is . If Rf=10K, calculate RF=19.5K.
For high pass and band pass filters, the output of the op amp is not required to be 0 at static state. And the single power supply operating mode can be selected. In the lowpass or bandstop filter circuit, it is a DCtoAC DC amplifier circuit, which generally requires the circuit to work in a dual power supply state.
Ⅴ Band Pass Filter Applications
The filtering circuit has a wide range of uses.According to different frequency amplitude characteristics, filter circuits can be divided into low pass filter circuit (LPF), highpass filter circuit (HPF), band pass filter circuit (BPF), band stop filter circuit (BEF) and allpass filter circuit (APF) . The BPF is mainly used to highlight signals in useful frequency bands and weaken signals or interference and noise in other frequency bands to improve the signaltonoise ratio. Therefore, band pass filters are often used in wireless receivers and transmitters to receive useful signals while preventing unwanted frequencies from passing through.
In addition to the fields of electronics and signal processing, an specific application of band pass filters is in the field of atmospheric sciences. A very common example is to use it to filter the weather data in the last 3 to 10 days, only the cyclone as a disturbance remains in the domain.
Frequently Asked Questions about Band Pass Filter
1. What is a bandpass filter used for?
A band pass filter is an electronic circuit or device which allows only signals between specific frequencies to pass through and attenuates/rejects frequencies outside the range. Band pass filters are largely used in wireless receivers and transmitters, but are also widely used in many areas of electronics.
2. What is the bandwidth of a bandpass filter?
The bandwidth of a bandpass filter is usually defined as the 3 dB bandwidth. Similarly, the 1 dB bandwidth is the point at which the signal amplitude decreases by 1 dB from its maximum value (above and below the center frequency).
3. How does bandpass filter work?
A bandpass filter works to screen out frequencies that are too low or too high, giving easy passage only to frequencies within a certain range. Bandpass filters can be made by stacking a lowpass filter on the end of a highpass filter, or vice versa. Attenuate means to reduce or diminish in amplitude.
4. How is bandpass filter calculated?
So all frequencies between the low cutoff frequecny and the high cutoff frequency are the passband of the bandpass filter. The gain of the circuit is determined by the formula, gain (AV)= R2/R1. Thus, for example, to have a gain of 10, R2 must be 10 times the value of R1.
5. What is the use of band pass filter?
Bandpass filters are widely used in wireless transmitters and receivers. The main function of such a filter in a transmitter is to limit the bandwidth of the output signal to the band allocated for the transmission. This prevents the transmitter from interfering with other stations.
Best Sales of diode
Photo  Part  Company  Description  Pricing (USD)  
AD588TQ883B  Company:Analog Devices Inc.  Remark:IC VREF SERIES 10V 16CERDIP 
Price:

Inquiry  
AD9057BRSZ40  Company:Analog Devices Inc.  Remark:IC ADC 8BIT PIPELINED 20SSOP 
Price:

Inquiry  
ADSP21375KSWZ2B  Company:Analog Devices Inc.  Remark:IC DSP 32BIT 266MHZ 208MQFP 
Price:

Inquiry  
ADSP2185MKCAZ300  Company:Analog Devices Inc.  Remark:IC DSP CONTROLLER 16BIT 144MBGA 
Price:

Inquiry  
ADSP2186MBSTZ266R  Company:Analog Devices Inc.  Remark:IC DSP CONTROLLER 16BIT 100LQFP 
Price:

Inquiry  
ADSP2188MKSTZ300  Company:Analog Devices Inc.  Remark:IC DSP CONTROLLER 16BIT 100LQFP 
Price:

Inquiry 
Alternative Models
Part  Compare  Manufacturers  Category  Description  
Mfr.Part#:S29GL01GS12TFIV10  Compare: S29GL01GS11TFI010 VS S29GL01GS12TFIV10  Manufacturers:Spansion  Category:Flash Memory  Description: NOR Flash Parallel 3V/3.3V 1Gbit 64M x 16Bit 120ns 56Pin TSOP Tray  
Mfr.Part#:S29GL01GS12TFIV10  Compare: Current Part  Manufacturers:Spansion  Category:Flash Memory  Description: NOR Flash Parallel 3V/3.3V 1Gbit 64M x 16Bit 120ns 56Pin TSOP Tray  
Mfr.Part#:S29GL01GS11TFI010  Compare: S29GL01GS12TFIV10 VS S29GL01GS11TFI010  Manufacturers:Spansion  Category:Flash Memory  Description: NOR Flash Parallel 3V/3.3V 1Gbit 64M x 16Bit 110ns 56Pin TSOP Tray  
Mfr.Part#:S29GL01GS11TFIV20  Compare: S29GL01GS12TFIV10 VS S29GL01GS11TFIV20  Manufacturers:Spansion  Category:Memory Chip  Description: NOR Flash Parallel 3V/3.3V 1Gbit 64M x 16Bit 110ns 56Pin TSOP Tray 
Ordering & Quality
Image  Mfr. Part #  Company  Description  Package  Qty  Pricing (USD)  
ADSPBF523KBCZ5  Company:Analog Devices Inc.  Remark:IC DSP 16BIT 533MHZ 289CSBGA  Package:N/A 
DataSheet 
In Stock:On Order Inquiry 
Price:

Inquiry  
ADSPBF547BBCZ5A  Company:Analog Devices Inc.  Remark:IC DSP 16BIT 533MHZ 400CSBGA  Package:N/A 
DataSheet 
In Stock:318 Inquiry 
Price:

Inquiry  
ADSPBF607BBCZ5  Company:Analog Devices Inc.  Remark:IC DSP CTRLR 349CSBGA  Package:N/A 
DataSheet 
In Stock:24 Inquiry 
Price:

Inquiry  
ADSPBF707BBCZ4  Company:Analog Devices Inc.  Remark:IC DSP LP 1024KB L2SR 184BGA  Package:N/A 
DataSheet 
In Stock:On Order Inquiry 
Price:

Inquiry  
AD202JN  Company:Analog Devices Inc.  Remark:IC OPAMP ISOLATION 2 CIRC 10DIP  Package:38DIP (0.600", 15.24mm), 11 Leads 
DataSheet 
In Stock:76 Inquiry 
Price:

Inquiry  
AD823ARZRL  Company:Analog Devices Inc.  Remark:IC OPAMP JFET 2 CIRCUIT 8SOIC  Package:8SOIC (0.154", 3.90mm Width) 
DataSheet 
In Stock:5000 Inquiry 
Price:

Inquiry  
AD8253ARMZRL  Company:Analog Devices Inc.  Remark:IC INST AMP 1 CIRCUIT 10MSOP  Package:10TFSOP, 10MSOP (0.118", 3.00mm Width) 
DataSheet 
In Stock:On Order Inquiry 
Price:

Inquiry  
AD8500AKSZREEL7  Company:Analog Devices Inc.  Remark:IC OPAMP GP 1 CIRCUIT SC705  Package:5TSSOP, SC705, SOT353 
DataSheet 
In Stock:On Order Inquiry 
Price:

Inquiry 
0 comment